Back

Trubuild

Overview Usage Product Specifications Handling Precautions
TRUBUILD WPL 333

Waterproofing Latex

 

TRUBUILD WPL 333 (WATERPROOFING LATEX) is a ready to use styrene butadiene latex (SBR). It is used for repairing of old construction like floor, beams slabs etc. and water proofing of toilets, kitchen, roof, bathroom and terraces. It has excellent bonding strength for old to new concrete and to plaster. It reduces shrinkage, cracking, etc.

Meets the requirements of ASTM C 579, IS: 9103-1999 & IS-101 (P-8/S-6):1993

Application
Applications
  • It can be used for different concrete repair application like spalled concrete, floor, columns, beams, slab & parapet etc.
  • Also, it can be used for water proofing of toilets, kitchen, bathroom and terraces.
  • It can be used as a bond coat and bonding mortar for old to new concrete for tiles & panel etc.
  • It can also be used as additive polymer for cement base injection grouting
  • It can be used for crack filling
  • It can be used as Anti-Corrosive Coating for reinforcement.
  • It is also used for water proofing of Retaining Wall, Swimming pool & RCC Water Tanks.
Application
Advantages
  • Free from chloride content.
  • Single component product and easy to use due to its low viscosity.
  • It prevents cracking, improves hardness & Flexural strength
  • It has excellent bonding on various substrates like concrete, masonry, stone work, plasters, and most of the building materials.
  • Excellent Cement Modifiers.
How to use
How to use

Surface Preparation

  • The surface should be clean by manual or mechanical means and it should be free from dust, unsound material, loose plaster, oil, paint, grease, algae and corrosion deposits. Roughen the any smooth surface by scrubbing. Surface should be brought to Saturated Surface Dry condition before the application of waterproof coating.

 

Mixing

  • For less than 25 kg, hand mixing is permissible, for quantity above to 25 kg use of Suitable Mechanical mixture is recommended to get proper homogeneous mixing.
  • Before application the surface should be thoroughly saturated with water and ensure removal of any excess water prior to application.

 

Water proof coating

  • For water proof coating make a slurry of 1:1.5 ratio (by volume) or 1:2 polymer to cement ratio (by weight) of Trubuild WPL 333 and cement. Charging of cement and mixing should be done slowly to avoid any air entrapment.
  • Apply 1st coat on surface and allow it to dry. After 4-6 hrs of first coat, apply second cost and then again allow it to dry for 5 -6 hrs. This should be followed by moist curing by sprinkling / Spraying of potable water for 24 hrs. After Moist curing, the surface should be allowed to air cure for 3 to 5 days before covering it with any protective screed.
  • Coverage will be 20 to 22 sq.ft/kg/2 coats

 

Renders & Patch repairing Mortar

  • For render and patching repair mortar application following quantities are to be mix (Cement: 50 kg, Sand: 150 kg, Trubuild WPL: 6-7.5 kg & Water: 10 lit) and this mix can be used as per the requirement.

 

Priming

  • For primer application used for bonding purpose make a slurry of 1:1 ratio (by volume) or 1:1.5 polymer to cement ratio (by weight) of Trubuild WPL 333 and cement. Apply one coat on surface. The repair or top mortar application should be carried out when then slurry coating is still tacky.

 

Screed & PCC Application

  • For screed & PCC application quantities are to be mix (Cement: 50 kg, Sand: 75 kg, 6 mm Coarse Aggregate: 75 kg, Trubuild WPL: 6-7.5 litres & Water: 10 lit) and this mix can be used as per the requirement.

 

TECHNICAL DETAILS

 

PROPERTIES STANDARD RESULTS
Physical state   Low Viscous liquid
Appearance   Opaque
Colour   Milky White
pH IS: 9103:1999 7-9
Specific Gravity   1.01-1.03
% Solid IS:101 (P-8/S-6):1993 36-40%
Compressive Strength ASTM C 579 30-40 N/mm²
Shelf Life
Shelf Life

24 months (Storage Temp 2 - 40°C)

Storage
Storage

Product should be stored in a dry place in their original, properly closed containers at temperature between 2 - 40°C. Partially emptied container should be closed immediately

Packing
  • Packing

    Bottle:
    200 gm, 500 gm, 1 kg, 5 kg, 10 kg, 20 kg & 50 kg

Application
Handling precautions

Mandatory and recommended industrial hygiene procedures should be followed whenever our products are being handled and processed. For additional information please consult the corresponding product data sheets and the brochure “Hygienic precautions for handling plastics products”.

X
Enquire Now